Keysight (Agilent) E4400B REPAIR and Keysight (Agilent) E4400B CALIBRATION
 
Custom-Cal has a high success rate in the repair of the Keysight (Agilent) E4400B. A calibration by Custom-Cal is performed by engineers with extensive OEM experience. We have the expertise and the necessary standards to perform the Keysight (Agilent) E4400B Calibration, onsite calibration may be available. We specialize in quick turnaround times and we can handle expedited deliveries upon request.

Need another Signal Generator?
Shop for Comparable Products on our  used Signal Generator page

 
   Keysight (Agilent) E4400B   Description / Specification:    
Keysight (Agilent) E4400B ESG-A 1000 MHz Analog RF Signal Generator

The HP E4400B 250 kHz to 1000 MHz is an ESG-A analog series RF signal generator. Resolution: 0.01 Hz. Switching Speed Modulation On: < 45 ms, typical. Switching Speed Modulation Off: < 35 ms, typical. Accuracy: Stability x fc timebase. Sweep Operating modes: Step: frequency and power, and arbitrary list. Sweep Dwell Time: 1 ms to 60 sec. Number of points: 2 to 401. Internal Reference Oscillator; Timebase Reference Output Frequency: 10 MHz, Amplitude: > 0.35 Vrms into 50 ohm load. External Reference Input; Frequency: 1, 2, 5, 10 MHz ± typ. 10 ppm (1 ppm, Option 1E5), Amplitude: > 0.15 Vrms, Input Impedance: 50 ohm. Output Range: 250 kHz to 1000 MHz +13 to -136 dBm (+17 to -136 dBm Option UNB). Output Resolution: 0.02 dB. Attenuator Hold Level Range: > 17 dB (>23 dB Option UNB). Switching Speed: < 25 ms typical (30 ms, Option UNB). SSB Phase Noise (typical, at 20 kHz offset) at 1000 MHz: < -116 dBc/Hz. Harmonics (<= + 4 dBm [<= +7.5 dBm, Option UNB] output level): < - 30 dBc. Frequency Modulation; Maximum Deviation: N x10 MHz. Resolution: 0.1% of deviation or 1 Hz, whichever is greater. Deviation Accuracy (1 kHz rate, dev. < N x 100 kHz): < ± (3.5% of FM deviation + 20 Hz). Phase Modulation; Maximum Deviation: N x 90 radians. Resolution: 0.1% of set deviation. Deviation Accuracy (1 kHz rate): < ± (5% of deviation + 0.01 radians). Pulse Modulation; On/Off Ratio: <= 1 GHz: > 80 dB. Rise/Fall Times: 150 ns, typical. Minimum Width (typical): ALC On: 2µs; ALC Off: 0.4µs. Level Accuracy (relative to CW)4 : ± 0.5 dB, typical. Internal Pulse Generator Squarewave Rates: 0.1 Hz-50 kHz. Pulse Period: 16 µs to 30 sec. Pulse Width: 8 µs to 30 sec. Interface: HP-IB (IEEE-488.2-1987) with Listen and Talk. RS-232. Options: 1EM, Move Connectors to Rear Panel. 1E5, Add High-Stability Timebase. UNB. High Power with mechanical attenuator



 

Standard Calibration $825.00 *
Click on Logo for More Prices
*This is a Web introductory price for one calibration of the Keysight (Agilent) E4400B. Price does not in most cases include measurement performance data. Pricing does include NIST traceable calibration and issue of a calibration certificate and calibration label. Pricing may vary slightly due to volume and location of laboratory supporting calibration. Volume pricing may apply. On-site fees may apply depending on logistics, location and volume of work to be completed during the visit.


Related Bench Equipment Terms and Definitions. For a complete list go to our  Terms and Definitions Page.

Clipping
Clipping is the limiting of a signal so that it never exceeds some threshold.

Line Regulation
Line regulation is the capability to maintain a constant output voltage level on the output channel of a power supply despite changes to the input voltage level.

Peak Envelope Power
Peak envelope power is the maximum value of the envelope power. Envelope power is measured by making the averaging time much less than 1/fm where fm is the maximum frequency component of the modulation waveform. The averaging time is therefore limited on both ends: (1) it must be small compared to the period of the highest modulation frequency, and (2) it must be large enough to be many RF cycles long.

RMS
RMS or root mean square is a statistical measure of the magnitude of a varying quantity

Please contact us for your Keysight (Agilent) E4400B REPAIR and/or Keysight (Agilent) E4400B ESG-A 1000 MHz Analog RF Signal Generator CALIBRATION
I'm interested in: 
Calibration Type (Select one):
Repair Information:
 Serial Number:

 Is there any physical damage?  
 If yes, describe:


What is the description of the problem?

How/when did the problem start?


 (*) Required Fields    For formal quote please fill in all fields.
Company:
From (Email):*
Contact Name:*
Country:*
Address 1:
Address 2:
City:
State/Territory/Province: *
Zip/Postal Code:
Phone:*

Comment: